BREWinfo (Pick from a category below or use the above search bar)

How to successfully open a microbrewery Part 2: Axe and Arrow Microbrewery

starting your own craft microbrewery brewpubIn this video, Josh, Krystle and Greg, the owners of Axe and Arrow Microbrewery in Glassboro, NJ discus how they started their successful microbrewery. They describe how they planned their craft brewery, where they located it and why, the equipment they purchased for their brewhouse and fermentation, their marketing approach, the permitting and licensing hurdles...

How to carbonate and serve beer directly from the BREWHA 4-in-1

carbonating directly in and serving from fermenter
The BREWHA 4-in-1 fermenters are designed to withstand up to 14.9psi of pressure. This is enough pressure to fully carbonate beer, and once carbonated, it is ready to serve. The BREWHA BIAC is the only system in the world that allow you to serve your beer directly from the vessel it is made in, ensuring you are drinking the tastiest...

How to successfully open a microbrewery Part 1: 3 Dogs Brewing

How to start a microbrewery This video is about building your own microbrewery. In it, 3 Dogs Brewing Co discusses how they went about opening their own successful microbrewery in a strip mall in Metro Vancouver. They discuss their vision for the brewery, the brew equipment they purchased, how they converted a former wine shop in a strip mall into a really...

BREWHA BIAC Instruction Manual

BIAC instruction manualWe are delighted that you have chosen a BREWHA BIAC for your home or microbrewing system! We trust that it will bring you many fun-filled hours of brewing, and of course, many times spent enjoying the fruit of your craft with your friends and customers.

This manual is meant to provide information on installation and setup of your beer brewing equipment, and...

How to assemble a grain roller mill for a microbrewery/brewpub

how to build a malt roller mill for microbrewery brewpub This video describes how to build a grist/malt roller mill for a microbrewery or brewpub. Starting with a Crankandstein 328G eight inch, three roller, fully geared mill, instructions are then given on how to connect a speed reducer and electric motor, and mount the assembly on a table for safe operation.

How to install and operate the BREWHA Keg Cleaner

Manual keg washer and cleanerThis manual keg cleaner is an economical way to manually clean kegs. The cleaner can stand alone or be set inside a BREWHA Large fermenter. Once spears are pulled, kegs can be inverted and dropped down onto the cleaner. When cleaning multiple kegs, it is simplest to...

The best way to clean and sanitize your stainless brewing equipment

Powder Brewers Wash One of the useful features of the BREWHA BIAC is that boiling can occur inside the fermenter which makes sanitation a snap—the heat of the boil will sanitize the fermenter so there is no need to chemically sanitize the vessel. All that is needed is to clean the fermenter out well with water and a soft cloth after the beer is removed, and it is ready to go for the next batch...

How to effectively clean electric heating elements

brewing element scrub brush for cleaningCleaning beer brewing elements is not difficult, especially with the BREWHA system where an element can be easily removed from the vessel simply be removing the clamp that holds it in place. Once removed...

Securing sanitary clamps against accidental loosening

sanitary clamp 1.5 A customer recently informed us that some friends (who were new to brewing) had loosened one of the sanitary clamps on the 'wrong' (that is, nearest to the fermenter) side of the valve. Instead of removing a hose fitting, they removed the entire valve and suddenly had beer spilling out of the fermenter. It is bad enough if...

Installing a portable fermentation temperature control unit

beer fermenting chiller For most styles of beer, a chilling system is important for producing a great tasting beverage. In fact, aside from proper sanitation, temperature control is arguably the single most important criteria for brewing a fantastic product. Without temperature control...

Preventing leaks and galling in the 4-in-1 fermenter

tighten fermenter lid so it doesn't leak
The 4-in-1 fermenter lid is held in place with eye bolts. Eye bolts are used over standard nuts as they are easier to open with fingers—no tools are necessary. However, when higher pressure is being applied to the vessel (up to 14.9psi), a tool is likely needed to tighten the lid down so it doesn't leak. For a tighter seal, a screw driver (or other steel bar) can be used to tighten the ring by...

Installing the 3-in-1 fermenter lid gasket

stainless conical lid gasketAll models of the BREWHA 3-in-1 fermenter have a silicone lid gasket for sealing the lid and providing up to 3psi of pressure for racking beer into kegs. If the lid is kept clean, the lid gasket can generally be kept in place as it can be sanitized simple by putting into position...

  • Visa
  • MasterCard
  • Amex