How to clean kegs with the BREWHA Keg Washer

CAUTION: when dealing with hot water it is important to always use protective gear including insulated wash gloves, full apron, and face mask. 

CAUTION: since kegs are stored under pressure, it is important to fully release all pressure before attempting to open a keg. Observe all safety steps recommended by your keg supplier.

The BREWHA Keg Washer is an economical manual cleaner that is an effective way to clean kegs. While chemicals can be used (and are recommended occasionally to remove any long term build up), the heat of the water is generally all that is needed to sanitize the kegs sufficient to safely store beer for several months.

This article discusses the washing of Sanke D kegs (the most common commercial kegs throughout North America) but the principles are the same for other commercial and homebrew kegs. To clean kegs, follow these steps:

1. Place the BREHWA Keg Washer inside the BREWHA fermenter or 120L Mash Tun, connect the Keg Washer return arm to the Keg Washer stand with the short 3/4" hose, 3/4" gaskets and clamps.  connect hoses inside keg cleaner vessel
connect keg washer to tap water for rinsing 2. To first rinse old beer out of the kegs, connect clean tap water to the Keg Washer. A short section of 1/2" silicone hose can be adapted for this. Clamp a 1/2" hose barb x 1.5"TC to one end, and a female garden hose x 1/2" hose barb (most hardware stores carry these) on the other. The hot tap water will flush the keg and rinse beer and sediment out. 
3. Release all gas in the keg by turning down on a Sanke spear removal tool (purchase online from keg suppliers) to fully depress the spear. Releasing all pressure before removing the spear is very important for safety reasons. (At all times follow all safety precautions recommended by the keg supplier.) release pressure from keg
removing keg retaining ring 4. Once the pressure is released, and with the spear removal tool still fully depressing the spear, remove the retaining ring that holds the spear in place. There are specific 'spear removal knives' like shown in the picture (can be purchased from keg suppliers online), but a small flat head screwdriver or other implement can also be used. The retaining ring is notched on each end so with the tool, move the ring towards the center until the end of it pops out of the channel that it sits in. This can be challenging the first few times, but with practice, a good method can be developed. Once the ring starts to pop out, it can be easily removed the rest of the way by gently pulling all around the ring with your fingers towards the middle of the keg. 
5. One the ring is removed, release and remove the spear removal tool and retainer ring. To withdraw the spear, it needs to be rotate about 5 degrees until the spear notch and keg groove line up. remove sanke spear
cleaning keg 6. The keg can then be lowered over the BREWHA Keg Washer spray ball until the keg rests on the supports. Tap water can be ran into the apparatus to rinse the keg out. The bottom dump valve on the fermenter (or other vessel) should be left open so the rinse water can drain. When using tap water, but especially with the near boiling water during the sanitize phase, it is important to wear insulated rubber wash gloves (like the ones resting on the pump in the picture below). 
 7. Once the kegs are rinsed, connect the BREWHA fermenter (or BREWHA 120L Mash Tun) to your recirculation pump. A powerful 1hp pump (like the commercial grade pump that we sell) is recommended as it provides a high pressure spray to aid with cleaning, but smaller pumps can be used as well. The larger hose (1"ID) provides water from the vessel to the pump, the smaller (3/4"ID) hose sends water from the pump back to the cleaner apparatus. connect pump to keg washer
fill water in keg cleaner to this level 8. Fill the vessel with water until the level is where the keg support arms meet the vertical pipe. If the water level is too low, the hot water evaporates more as it falls back into the vessel, and the heating element has to work harder. Ensure the heating element is always completely covered with ample water. Heat the water to just shy of boiling. 
9. The keg spear can be put into the boiling water to heat sanitize it. The spear can be inverted to let water fill the spear and to ensure that the head is fully sanitized. Drop the keg over the spray ball, turn the pump on and let it spray hot, sanitizing water into the keg for about 2 minutes. Then turn the pump off. Sanitize keg spear
how to install spear back into keg 10. Once the water drains out of the keg, remove the keg and spear (remember to wear insulated wash gloves as they will be hot), lower the spear back into the keg and with the help of the spear removal tool (this should be heat sanitized too so it doesn't infect the top of the spear) put the retaining ring back in place. It is generally easiest to replace the ring if it is started into the groove about 60 degrees clockwise from the locking tab. This ensures that the beginning and end of the ring are not located at either of the two locking tabs. 
11. The final step is to add CO2 to the kegs at this point to purge out the oxygen and pressurize the kegs (optional) so that they are ready to fill with beer (don't add more CO2 pressure than the pressure of the fermenter or CO2 will blow back into the fermenter; e.g. if the fermenter is at 12psi, fill the kegs to not more than 12psi). CO2 can be added with the same hose with which you fill the kegs with beer. By simply connecting a Gas in Post to the Fermenter to Keg Racking Hose CO2 can be easily added to your kegs. (To permit CO2 or beer to flow 'backwards' through the Sanke coupler, the check valves need to be first removed. It is recommended to keep a dedicated coupler just for racking beer. See more details on removing the checks at the bottom of this page). adding co2 to purge kegs

 

Once the kegs are purged they are ready for filling with beer. If you won't be filling right away, cap the top of the keg to keep it clean; 2" TC plastic covers (like the plastic caps that come with the BREWHA 2" butterfly valves) work great for this or tin foil or caps can be purchased online from keg suppliers.

Learn: Transferring beer from a fermenter to a keg
BREWHA Keg Washer product page

Leave a comment